Page 14 of 18

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Thu Jul 04, 2019 12:33 pm
by luckz
Is this a known issue on the older version?
islc.png
(seems to happen a lot when updating big[?] Steam games)

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Thu Jul 04, 2019 12:36 pm
by Wagnard
luckz wrote:
Thu Jul 04, 2019 12:33 pm
Is this a known issue on the older version?

islc.png

(seems to happen a lot when updating big[?] Steam games)
Humm never encountered this on my end.
If you can repro this and also give me a screenshot of task manager memory usage.

But before that, use the latest version as this could. Be an old and resolved issue.
Thanks

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Thu Jul 04, 2019 7:15 pm
by willybony
In the version v1.0.1.3, the Polling Rate is for the mouse? Why Polling Rate(ms) instead of Polling Rate (Hz)?

I tested it with Logitech G203 and polling rate doesnt change, stuck in 1000hz always.

Thank you for this nice piece of software.

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Thu Jul 04, 2019 7:16 pm
by Wagnard
willybony wrote:
Thu Jul 04, 2019 7:15 pm
In the version v1.0.1.3, the Polling Rate is for the mouse? Why Polling Rate(ms) instead of Polling Rate (Hz)?

I tested it with Logitech G203 and polling rate doesnt change, stuck in 1000hz always.

Thank you for this nice piece of software.
No not at all, it's the rate that the application will check the memory status.

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Thu Jul 04, 2019 7:24 pm
by willybony
Wagnard wrote:
Thu Jul 04, 2019 7:16 pm

No not at all, it's the rate that the application will check the memory status.
Ok understood, thanks.

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Fri Jul 05, 2019 5:51 am
by Kuliman
I decided to use this program, it works, but does not want to clean automatically, but manually everything works fine, I tried version 2 1.0.1.0 and 1.0.1.3 and only manual cleaning works there and there, what can I do?

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Fri Jul 05, 2019 9:56 am
by Wagnard
Kuliman wrote:
Fri Jul 05, 2019 5:51 am
I decided to use this program, it works, but does not want to clean automatically, but manually everything works fine, I tried version 2 1.0.1.0 and 1.0.1.3 and only manual cleaning works there and there, what can I do?
From the screenshot, it is normal it doesn't clean, you have more than 1024mb free memory.
Both conditions must be met.

Re: Intelligent standby list cleaner (ISLC) v1.0.1.3 Released

Posted: Sat Jul 06, 2019 4:29 am
by Kuliman
Wagnard wrote:
Fri Jul 05, 2019 9:56 am
Kuliman wrote:
Fri Jul 05, 2019 5:51 am
I decided to use this program, it works, but does not want to clean automatically, but manually everything works fine, I tried version 2 1.0.1.0 and 1.0.1.3 and only manual cleaning works there and there, what can I do?
From the screenshot, it is normal it doesn't clean, you have more than 1024mb free memory.
Both conditions must be met.
Ok thanks, I just thought that it was malfunctioning, but it turns out that my brain did not work properly ...

Re: Intelligent standby list cleaner (ISLC) v1.0.1.5 Released

Posted: Wed Jul 10, 2019 8:14 am
by oldfart
Hi, thanks for the tool. I used to clear the standby list when needed with Sysinternals' Rammap, but this is much easier.
I have a small typo to report, see the yellow marked part in the screenshot below.

Capture.JPG

Re: Intelligent standby list cleaner (ISLC) v1.0.1.5 Released

Posted: Wed Jul 10, 2019 3:15 pm
by Wagnard
oldfart wrote:
Wed Jul 10, 2019 8:14 am
Hi, thanks for the tool. I used to clear the standby list when needed with Sysinternals' Rammap, but this is much easier.
I have a small typo to report, see the yellow marked part in the screenshot below.


Capture.JPG
Opps, thanks for reporting.